TY - JOUR
T1 - Design of ceramic materials for chemical sensors
T2 - Effect of SmFeO3 processing on surface and electrical properties
AU - Aono, Hiromichi
AU - Sato, Masaki
AU - Traversa, Enrico
AU - Sakamoto, Masatomi
AU - Sadaoka, Yoshihiko
PY - 2001
Y1 - 2001
N2 - Perovskite-type SmFeO3 powders were prepared by the thermal decomposition of a heteronuclear complex, Sm(Fe(CN)6) 4H2O and by solid-state reaction between the corresponding single oxides, Sm2O3 and Fe2O3. The thermal decomposition behavior of the complex was studied by thermogravimetric analysis. X-ray diffractometry was used to investigate the structure of the products from the complex thermal decomposition and the formation of SmFeO3 from the oxide mixture. Powders prepared by both methods were used to deposit thick films onto alumina substrates with comb-type gold electrodes. The microstructure and chemical homogeneity of the film surfaces were investigated by scanning electron microscopy and Auger electron spectroscopy. Thick SmFeO3 single-phase films having a homogeneous elemental distribution on the surface were obtained when powder prepared by thermal decomposition of the complex was used for deposition, even when the powder was fired at low temperature (800 °C). Surface chemical analysis was performed by X-ray photoelectron spectroscopy (XPS). The O 1s XPS line was deconvoluted into two peaks, attributed to adsorbed oxygen (Oad) and oxygen in the lattice (Olattice). Quantitative analysis showed that the surface coverage of iron, expressed as Fe/(Fe+Sm), was larger for the films prepared using the solid-state reacted powder. Although the Olattice/(Fe+Sm) atomic ratio was not influenced by the processing procedures (and, thus, by iron surface coverage), the amount of Oad decreased with increasing iron surface coverage. A model of the SmFeO3 surface was used to determine that the outermost layer of the perovskite-type SmFeO3 prepared from the complex consisted mainly of samarium ions that could each bond four adsorbed oxygen ions. A single oxygen ion could adsorb onto an iron ion, and therefore, the content of adsorbed oxygen was lower for the film prepared from the solid-state reacted powders, which showed larger iron surface coverage. Electrical conductance measurements, performed with increasing temperature in different gaseous environments, confirmed these findings. Higher conductances and lower activation energies were observed for the films with larger samarium surface coverage.
AB - Perovskite-type SmFeO3 powders were prepared by the thermal decomposition of a heteronuclear complex, Sm(Fe(CN)6) 4H2O and by solid-state reaction between the corresponding single oxides, Sm2O3 and Fe2O3. The thermal decomposition behavior of the complex was studied by thermogravimetric analysis. X-ray diffractometry was used to investigate the structure of the products from the complex thermal decomposition and the formation of SmFeO3 from the oxide mixture. Powders prepared by both methods were used to deposit thick films onto alumina substrates with comb-type gold electrodes. The microstructure and chemical homogeneity of the film surfaces were investigated by scanning electron microscopy and Auger electron spectroscopy. Thick SmFeO3 single-phase films having a homogeneous elemental distribution on the surface were obtained when powder prepared by thermal decomposition of the complex was used for deposition, even when the powder was fired at low temperature (800 °C). Surface chemical analysis was performed by X-ray photoelectron spectroscopy (XPS). The O 1s XPS line was deconvoluted into two peaks, attributed to adsorbed oxygen (Oad) and oxygen in the lattice (Olattice). Quantitative analysis showed that the surface coverage of iron, expressed as Fe/(Fe+Sm), was larger for the films prepared using the solid-state reacted powder. Although the Olattice/(Fe+Sm) atomic ratio was not influenced by the processing procedures (and, thus, by iron surface coverage), the amount of Oad decreased with increasing iron surface coverage. A model of the SmFeO3 surface was used to determine that the outermost layer of the perovskite-type SmFeO3 prepared from the complex consisted mainly of samarium ions that could each bond four adsorbed oxygen ions. A single oxygen ion could adsorb onto an iron ion, and therefore, the content of adsorbed oxygen was lower for the film prepared from the solid-state reacted powders, which showed larger iron surface coverage. Electrical conductance measurements, performed with increasing temperature in different gaseous environments, confirmed these findings. Higher conductances and lower activation energies were observed for the films with larger samarium surface coverage.
UR - http://www.scopus.com/inward/record.url?scp=0035249786&partnerID=8YFLogxK
U2 - 10.1111/j.1151-2916.2001.tb00660.x
DO - 10.1111/j.1151-2916.2001.tb00660.x
M3 - Article
AN - SCOPUS:0035249786
SN - 0002-7820
VL - 84
SP - 341
EP - 347
JO - Journal of the American Ceramic Society
JF - Journal of the American Ceramic Society
IS - 2
ER -