TY - JOUR
T1 - Unambiguously Enhanced Ultraviolet Luminescence of AlGaN Wavy Quantum Well Structures Grown on Large Misoriented Sapphire Substrate
AU - Sun, Haiding
AU - Mitra, Somak
AU - Subedi, Ram Chandra
AU - Zhang, Yi
AU - Guo, Wei
AU - Ye, Jichun
AU - Shakfa, Mohammad Khaled
AU - Ng, Tien Khee
AU - Ooi, Boon S.
AU - Roqan, Iman S.
AU - Zhang, Zihui
AU - Dai, Jiangnan
AU - Chen, Changqing
AU - Long, Shibing
N1 - KAUST Repository Item: Exported on 2020-10-01
Acknowledgements: The authors acknowledge the funding support from University of Science and Technology of China (KY2100000081), Chinese Academy of Science Funding, National Natural Science Foundation of China (Grant Nos. 61905236 and 61704176), and King Abdullah University of Science and Technology baseline (KAUST) funding (BAS/1/1614-0101). This work was partially carried out at the University of Science and Technology of China Center for Micro and Nanoscale Research and Fabrication.
PY - 2019/1/1
Y1 - 2019/1/1
N2 - High-quality epitaxy consisting of Al1−xGaxN/Al1−yGayN multiple quantum wells (MQWs) with sharp interfaces and emitting at ≈280 nm is successfully grown on sapphire with a misorientation angle as large as 4°. Wavy MQWs are observed due to step bunching formed at the step edges. A thicker QW width accompanied by a greater accumulation of gallium near the macrostep edge than that on the flat-terrace is observed on 4° misoriented sapphire, leading to the generation of potential minima with respect to their neighboring QWs. Consequently, a significantly enhanced photoluminescence intensity (at least ten times higher), improved internal quantum efficiency (six times higher at low excitation laser power), and a much longer carrier lifetime are achieved. Importantly, the wafer-level output-power of the ultraviolet light emitting diodes on 4° misoriented substrate is nearly increased by 2–3 times. This gain is attributed to the introduction of compositional inhomogeneities in AlGaN alloys induced by gallium accumulation at the step-bunched region thus forming a lateral potential well for carrier localization. The experimental results are further confirmed by a numerical modeling in which a 3D carrier confinement mechanism is proposed. Herein, the compositional modulation in active region arising from the substrate misorientation provides a promising approach in the pursuit of high-efficient ultraviolet emitters.
AB - High-quality epitaxy consisting of Al1−xGaxN/Al1−yGayN multiple quantum wells (MQWs) with sharp interfaces and emitting at ≈280 nm is successfully grown on sapphire with a misorientation angle as large as 4°. Wavy MQWs are observed due to step bunching formed at the step edges. A thicker QW width accompanied by a greater accumulation of gallium near the macrostep edge than that on the flat-terrace is observed on 4° misoriented sapphire, leading to the generation of potential minima with respect to their neighboring QWs. Consequently, a significantly enhanced photoluminescence intensity (at least ten times higher), improved internal quantum efficiency (six times higher at low excitation laser power), and a much longer carrier lifetime are achieved. Importantly, the wafer-level output-power of the ultraviolet light emitting diodes on 4° misoriented substrate is nearly increased by 2–3 times. This gain is attributed to the introduction of compositional inhomogeneities in AlGaN alloys induced by gallium accumulation at the step-bunched region thus forming a lateral potential well for carrier localization. The experimental results are further confirmed by a numerical modeling in which a 3D carrier confinement mechanism is proposed. Herein, the compositional modulation in active region arising from the substrate misorientation provides a promising approach in the pursuit of high-efficient ultraviolet emitters.
UR - http://hdl.handle.net/10754/660161
UR - https://onlinelibrary.wiley.com/doi/abs/10.1002/adfm.201905445
UR - http://www.scopus.com/inward/record.url?scp=85073953290&partnerID=8YFLogxK
U2 - 10.1002/adfm.201905445
DO - 10.1002/adfm.201905445
M3 - Article
SN - 1616-301X
VL - 29
SP - 1905445
JO - Advanced Functional Materials
JF - Advanced Functional Materials
IS - 48
ER -